Crack Repair and Adhesives

AT-XP High-Strength Acrylic Adhesive

AT-XP is an acrylic-based high-strength anchoring adhesive. AT-XP is a 10:1 ratio, two-component, anchoring adhesive for use in threaded rod and rebar into concrete (cracked and uncracked) and masonry (uncracked) under a wide range of conditions. AT-XP adhesive dispenses easily in cold or warm environments and in below-freezing temperatures with no need to warm the cartridge.

SET-XP High-Strength Epoxy Adhesive

Simpson Strong-Tie SET-XP is an epoxy-based high-strength anchoring adhesive. SET-XP is a 1:1 ratio, two-component anchoring adhesive for anchoring and doweling into concrete (cracked and uncracked) and masonry (uncracked) applications.

Rapid Flex CJ

RAPID FLEX CJ is a 100% solids, two component, UV resistant, semi-rigid, rapid curing, polyurea for filling control
and construction joints in industrial concrete floors.  RAPID FLEX CJ allows for joints to be shaved quickly for
fast turnaround.  RAPID FLEX CJ can also be used for the repair of damaged or spalled joint nosing and cracks.

SpecChem SpecPoxy 3000-FS

SPECPOXY 3000 FS is a two component, moisture insensitive, high modulus, structural epoxy bonding gel. SPECPOXY 3000 FS is 100% solids, solvent free, low odor, high strength, and non-sag.  It is used to anchors bolts, dowels, and reinforcing steel, vertical and overhead structural bonding and patching, sealing of cracks, and the setting of injection ports. SPECPOXY 3000 FS is for use in concrete, block, brick, or stone.

 

SealBoss 6500 Joint Filler

SealBoss 6500 QuickFix is a high quality joint and crack filler for concrete substrates in applications that are time critical. It works well in adverse temperature conditions as the material cures in ambient temperatures from -28°C (‑20°F) to 54°C (130°F). The tack free time is 5 to over 15 minutes depending on temperature.

 

 

 

SealBoss 6060 Crack & Spall Repair

SealBoss 6060 QuickFix is an advanced polyurethane formulated, low viscosity, rapid set, high strength, ultra low viscosity, self leveling, two component, 1:1 ratio by volume, 100% solids repair material. This strong and rigid material has been designed to fix spalled concrete surfaces and cracks, and to rebuild damaged control joints effectively and quickly.  SealBoss 6060 QuickFix works for concrete and asphalt repairs. The product penetrates into small cracks and forms a high strength adhesive bond between broken structures with the benefit of sealing the base against further erosion from water in outside applications.

SealBoss 1500 Hot Shot

SealBoss® 1500 WaterStopFoam is a hydrophobic, wateractivated (hydro-active), water cut-off grout and foam seal
grout based on a phthalate free, MDI polyurethane. The product is 100% solvent free, 100% solids two component
formulation to be mixed at a 1:1 ration by volume. Upon contact with water SealBoss® 1500 WaterStopFoam reacts
to a semi flexible foam while expanding its volume 30 to 40 times. The cured material is of a constant volume. Since water is not a component of the foam structure, the cured material is essentially not effected by water or dryness. The reacted material essentially does not shrink or swell.  The advanced 1:1 formulation of the product results in a very dense, closed cell structure when injected under pressure.  Very low counter pressure will result in a less rigid more expanded product. For best waterproofing results a closed cell structure is desired.

Roadware Matchcrete Clear

Roadware MatchCrete Clear is a two component aliphatic polyurethane for repairing cracks, spalls, and joints in concrete subject to UV exposure from sunlight. This material is clear in appearance when applied and cured. Colored sand and pigments may be added to create color stable repairs that match most any decorative style or shade of concrete surface. MCC will not significantly change color with exposure to sunlight over time.  Roadware MatchCrete Clear is used to quickly repair cracks and spalls in concrete that is exposed to sunlight and a color compatible appearance over time is desired.

Roadware 10 Minute Mender

Roadware 10 Minute Concrete Mender is a high-penetration two-part hybrid urethane that combines with sand to form a tough instant polymer concrete. This nearly water thin formula is designed Microdowel deep into the host concrete creating extremely high bond strengths, reinforcement of the repair area as well as permanent repairs.  Roadware 10 Minute Concrete Mender produces polymer concrete repairs that absorb the shock and transfers the load of heavy traffic without cracking or disbonding. It is highly chemically resistant and can be applied in a wide range of temperatures. It is excellent for industrial floor repairs subject to forklift traffic and harsh conditions.